Difference between revisions of "WRT54G"
| Line 25: | Line 25: | ||
Changes to current XINU revision for 'G' compatibility (not finished): | Changes to current XINU revision for 'G' compatibility (not finished): | ||
| − | * loader | + | * loader/start.S |
| + | ** change max physical address from 0x81000000 to 0x80800000 (cut in half) | ||
** removal of cfe_api.c from loader, remove references in start.S | ** removal of cfe_api.c from loader, remove references in start.S | ||
| − | ** replaced CFE cache flushing with fresh cache init function in | + | ** replaced CFE cache flushing with fresh cache init function |
| − | * | + | ** altered mips.h for macros in loader cache init function |
| − | * uartInit.c | + | * system/xdone.c - remove CFE_exit() |
| + | * uart/uartInit.c | ||
** remove '''ucptr->uart_dll = 0x0B;''' | ** remove '''ucptr->uart_dll = 0x0B;''' | ||
** remove '''ucptr->uart_dlm = 0x00;''' | ** remove '''ucptr->uart_dlm = 0x00;''' | ||
| Line 35: | Line 37: | ||
* devtable.c | * devtable.c | ||
** remove entries for SERIAL1 and TTY1 | ** remove entries for SERIAL1 and TTY1 | ||
| − | ** I further changed the CONSOLE to be device 1, rather than 2 | + | ** I further changed the CONSOLE to be device 1, rather than 2 |
| − | + | * device.h | |
| − | + | ** remove lines for #define SERIAL1 and TTY1 | |
| − | + | ** define CONSOLE and TTY0 as 1, rather than 2 | |
| − | ** | + | ** change #define NUART and NTTY from 2 to 1 |
| − | + | ||
| − | |||
Presently, the serial port appears to function properly, although interaction with the CONSOLE causes XINU to lock-up | Presently, the serial port appears to function properly, although interaction with the CONSOLE causes XINU to lock-up | ||
| + | It now appears to be related to the interrupt handler, possibly dating back to the rough changes in start.S | ||
Revision as of 22:42, 11 June 2007
Transceiver from GL causes dropped characters; using Linksys transceiver
- possibly solved by "tighter" transceiver construction
loading CFE
VxWorks will flash over itself with CFE - http://wiki.openwrt.org/OpenWrtDocs/Hardware/Linksys/WRT54G
Attempted to load micro openWRT kernel and CFE over VxWorks
- upload failed - incompatible browser?
- despite successful re-load of original firmware, bootloader refuses to find image on flash
- possible solutions are loading fresh VxWorks from network or reloading flash through EJTAG port
loading XINU
Control-C interrupts VxWorks loader, as it does in CFE. VxWorks has an advantage over CFE in that it will remember bootloader settings for tftp host after powercycle. This removes the need for special xinu-console script to talk to CFE. Just run xinu-console, download compiled boot image, and powercycle.
Settings for VxWorks bootloader:
- boot device: vl0
- host name: morbius
- file name: {backend name}.boot
- inet on ethernet: 192.168.6.{assigned by morbius}
- host inet: 192.168.6.10
- flags 0x88 --tftp and quickboot
Changes to current XINU revision for 'G' compatibility (not finished):
- loader/start.S
- change max physical address from 0x81000000 to 0x80800000 (cut in half)
- removal of cfe_api.c from loader, remove references in start.S
- replaced CFE cache flushing with fresh cache init function
- altered mips.h for macros in loader cache init function
- system/xdone.c - remove CFE_exit()
- uart/uartInit.c
- remove ucptr->uart_dll = 0x0B;
- remove ucptr->uart_dlm = 0x00;
- If one queries the hardware values to replace 0B and 00 can be identified, but it is not necessary (and the values it gave me, 0 and 1 respectively, did not work)
- devtable.c
- remove entries for SERIAL1 and TTY1
- I further changed the CONSOLE to be device 1, rather than 2
- device.h
- remove lines for #define SERIAL1 and TTY1
- define CONSOLE and TTY0 as 1, rather than 2
- change #define NUART and NTTY from 2 to 1
Presently, the serial port appears to function properly, although interaction with the CONSOLE causes XINU to lock-up
It now appears to be related to the interrupt handler, possibly dating back to the rough changes in start.S
