Difference between revisions of "Build Backend Pool"

From Embedded Xinu
Jump to navigation Jump to search
Line 34: Line 34:
  
 
== The Server ==
 
== The Server ==
 +
 +
Our XINU Server is a PowerPC G5 XServe running Fedora Core Linux.  We use this configuration as a model for the information below, but other architecture / O/S combinations are known to work, and there's no reasons this shouldn't work for virtually any machine with two network interfaces running a modern UNIX O/S.
  
 
=== DHCP Daemon ===
 
=== DHCP Daemon ===
 +
 +
Many modern firmware implementations will allow a device to automatically acquire an IP address using the DHCP protocol even before the O/S kernel begins to boot.  The [[CFE]] on our Linksys backends will attempt to configure its primary ethernet interface when issued the command, "ifconfig -auto eth0"
 +
over the serial console.  See [[HOWTO:Run your own code]] for more details.
 +
 +
In our configuration, the XINU Server runs a DHCP daemon that is configured to supply addresses to backends on the private network.  We use the
 +
standard dchp server package that comes stock with our Linux distribution (dhcp-3.0.5-3.fc6, as of this writing).  Here is a sample configuration
 +
file, dhcpd.conf.  Our configuration supplies a fixed IP address for each backend, based upon MAC address.  It is important to note that the
 +
"filename" field designates a unique boot image for each backend; this allows each backend to boot a distinct image, customized by the student currently
 +
connected to that backend's serial console.
  
 
=== TFTP Daemon ===
 
=== TFTP Daemon ===

Revision as of 04:25, 22 March 2007

Summary

This page details how to scale your laboratory environment up to a pool of backend target machines available for remote access.

The Big Picture

XINU-Lab-schematic.gif

XINU Backends

Backend targets upload a student's kernel over a private network on boot, and run the O/S directly. No simulations or emulation are involved; this is real hardware.

MIPS targets: We use Linksys WRT54GL wireless routers (~$60) with serial port modifications (~$10) running an embedded MIPS32 200MHz processor, 4 MB flash, 16 MB RAM, two UARTs, wired and wireless network interfaces.

PowerPC targets: We use Apple G3 desktops (recycled) with 512 MB RAM, linear framebuffer, PCI bus, NIC, HD. Apple G4 MiniMac also supported.

CISC targets: Classic XINU runs on Intel x86, Sun 3/Motorola 68K, Sparc, and VAX, among others.

XINU Server

A general purpose server with multiple network interfaces manages a private network for the XINU backends, using standard network protocols like DHCP and TFTP.

Backend serial consoles can connect directly to server's serial ports, or, in larger installations, to a serial annex or concentrator that allows many more serial ports.

A daemon running on the server allows users on frontend workstations to remotely access backend serial consoles, or upload fresh kernels. Optional rebooting hardware allows clients to remotely reset crashed backends.

Our Console Tools are freely available for modern UNIX platforms, including Fedora Linux and Solaris.

XINU Frontends

General purpose computer laboratory workstations can compile the XINU kernel, using a standard GNU C compiler and UNIX toolchain. GCC crosscompilers are readily available when the frontend architecture does not match the backend architecture.

Backend consoles can be connected directly to frontend serial ports, or frontends can communicate with the server daemon that manages collections of backend serial consoles.

With fully remote console access, kernel upload and powercycling, any machine on the network is a potential frontend, and need not be physically near the XINU server and laboratory hardware. Students can work on their operating system projects from their dorm room computers.

Additional (Optional) hardware

The Server

Our XINU Server is a PowerPC G5 XServe running Fedora Core Linux. We use this configuration as a model for the information below, but other architecture / O/S combinations are known to work, and there's no reasons this shouldn't work for virtually any machine with two network interfaces running a modern UNIX O/S.

DHCP Daemon

Many modern firmware implementations will allow a device to automatically acquire an IP address using the DHCP protocol even before the O/S kernel begins to boot. The CFE on our Linksys backends will attempt to configure its primary ethernet interface when issued the command, "ifconfig -auto eth0" over the serial console. See HOWTO:Run your own code for more details.

In our configuration, the XINU Server runs a DHCP daemon that is configured to supply addresses to backends on the private network. We use the standard dchp server package that comes stock with our Linux distribution (dhcp-3.0.5-3.fc6, as of this writing). Here is a sample configuration file, dhcpd.conf. Our configuration supplies a fixed IP address for each backend, based upon MAC address. It is important to note that the "filename" field designates a unique boot image for each backend; this allows each backend to boot a distinct image, customized by the student currently connected to that backend's serial console.

TFTP Daemon

XINU Console Daemon

The XINU Console Daemon and various associated utilities provide network clients with connectivity to backend consoles that are really only connected directly to the console host. The xinu-console software package is now freely available for UNIX console hosts and front end clients.

(GZipped tarball xinu-console-2.02.tar.gz)

(Fedora Core Source RPM xinu-console-2.02-2.src.rpm)

The Client

Cross-Compiler

Console Access

Security

A word on security