Difference between revisions of "EJTAG"

From Embedded Xinu
Jump to navigation Jump to search
 
(One intermediate revision by one other user not shown)
Line 9: Line 9:
  
 
== Debugging ==
 
== Debugging ==
Attempting to use GNU debugger: http://www.gnu.org/software/gdb.  GDP uses its own Remote Serial Protocol (RDB) to communicate to remote targets.  This protocol could be used to communicate with the XINU backends through the current serial connection.  Although, this would require additions to XINU: communication with the GDB host; altering of exception handler to allow GDB to take control of target processor.
+
Attempting to use GNU debugger: http://www.gnu.org/software/gdb.  GDB uses its own Remote Serial Protocol (RDB) to communicate to remote targets.  This protocol could be used to communicate with the XINU backends through the current serial connection.  Although, this would require additions to XINU: communication with the GDB host; altering of exception handler to allow GDB to take control of target processor.
  
 
The use of the EJTAG port on the WRT54-series routers gives the user hardware control of the processor, avoiding the need for strategically placed breakpoints and XINU interrupt subsystem modification.  Additionally, requests by the debugger for specicfic data can be aquired directly from registers.  The trick to this operation is software that can interpret commands from RDB into EJTAG signals to be sent through the host parallel port, and vice-versa.  An implementation of this interpreter can be found at http://www.totalembedded.com/open_source/jtag/mips32_ejtag.php.
 
The use of the EJTAG port on the WRT54-series routers gives the user hardware control of the processor, avoiding the need for strategically placed breakpoints and XINU interrupt subsystem modification.  Additionally, requests by the debugger for specicfic data can be aquired directly from registers.  The trick to this operation is software that can interpret commands from RDB into EJTAG signals to be sent through the host parallel port, and vice-versa.  An implementation of this interpreter can be found at http://www.totalembedded.com/open_source/jtag/mips32_ejtag.php.
Line 28: Line 28:
 
[[Image:Wiggler.png|thumb|700px|center|"wiggler" clone from OpenWRT]]
 
[[Image:Wiggler.png|thumb|700px|center|"wiggler" clone from OpenWRT]]
 
[[Image:JTAGunbuffered.png|thumb|400px|center|unbuffered cable from OpenWRT; used by de-brick utility]]
 
[[Image:JTAGunbuffered.png|thumb|400px|center|unbuffered cable from OpenWRT; used by de-brick utility]]
 +
[[Image:Xinu-Wiggler.png|thumb|700px|center|Our current buffer/wiggler setup]]
  
 
== See also ==
 
== See also ==
 
* [[EJTAG ID Codes and Implementation Registers]]
 
* [[EJTAG ID Codes and Implementation Registers]]

Latest revision as of 03:13, 11 September 2010

EJTAG is a MIPS-specific extension of IEEE 1149.1, the Joint Test Action Group. Allows interfacing with additional logic in SoC

  • direct control of processor for step-by-step debugging
  • access to busses and registers
    • aids in debugging
    • possible usage as additional peripheral data bus
    • direct writing to flash for firmware updates (and de-bricking)


Debugging

Attempting to use GNU debugger: http://www.gnu.org/software/gdb. GDB uses its own Remote Serial Protocol (RDB) to communicate to remote targets. This protocol could be used to communicate with the XINU backends through the current serial connection. Although, this would require additions to XINU: communication with the GDB host; altering of exception handler to allow GDB to take control of target processor.

The use of the EJTAG port on the WRT54-series routers gives the user hardware control of the processor, avoiding the need for strategically placed breakpoints and XINU interrupt subsystem modification. Additionally, requests by the debugger for specicfic data can be aquired directly from registers. The trick to this operation is software that can interpret commands from RDB into EJTAG signals to be sent through the host parallel port, and vice-versa. An implementation of this interpreter can be found at http://www.totalembedded.com/open_source/jtag/mips32_ejtag.php.


Specific Implementations

So far, development has focused exclusively on the WRT54GL. For anyone investigating the capabilities of the WRT54GL EJTAG system, note the instruction register size is a full 8 bits, not the 5 bits required by specification. Believing the 54GL CP0 Debug Program Counter register to be returning erroneous addresses, headers are being added to a 54G v.8, and a 350N v.1. For IDCODEs and implementation register values check EJTAG ID Codes and Implementation Registers.


Probes

Images are of three variant EJTAG connections. The first two buffered by active line drivers, the last passive. Xinu research is currently using an active probe similar to the OpenWRT "Wiggler" clone; although, the parallel port pinouts match the unbuffered cable diagram. Note that the unbuffered cable at the bottom of this page is only proven by xinu research functional in writing to the Test Access Port. It may not read data back from the target device. Additionally, rumor claims that the cable can be no longer than 6" (not 6'). This is partially substantiated by photographs "out there" of similar 6 inch cables used with a variety of devices.


Total Embedded buffered cable
"wiggler" clone from OpenWRT
unbuffered cable from OpenWRT; used by de-brick utility
Our current buffer/wiggler setup

See also