Flash driver

From Embedded Xinu
Revision as of 20:14, 29 July 2009 by Michael (talk | contribs) (Updated the Flash driver page)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

Embedded Xinu uses a multi-layered approach to dealing with Flash memory. This allows the presentation of a simple and consistent interface to user programs, while handling the more complicated hardware interface underneath.

High level API

Like other drivers in Embedded Xinu, the Flash driver provides user level calls to open(), close(), read(), write(), and control(). In order to begin using a device the user must open() it, this initializes the logical layer and sets up structures for use. The complimentary close() function will clear those structures and write any cached data to the underlying Flash hardware.

control() provides several functions for getting information and performing operations on the driver. The control functions are presented below.

  • FLASH_BLOCK_SIZE returns the size of logical blocks for the Flash device.
  • FLASH_N_BLOCKS returns the number of block available on the Flash device.
  • FLASH_SYNC forces a synchronization from cached data onto Flash memory, the two forms are:
    • FLASH_BLOCK synchronizes a specific erase block, and
    • FLASH_LOGBLOCK synchronizes a logical block of data.

read() and write()

The Flash device takes three slightly different parameters for read() and write() when compared to other devices in Embedded Xinu. Normal devices will take the device identifier, a buffer, and the size of the buffer. Since the Flash device uses fixed size logical blocks, it is assumed that the buffer will be the size of a single logical block. Therefore, the Flash driver API for read() and write() is:

read(int device_id, char *buffer, uint block_number);
write(int device_id, char *buffer, uint block_number);

Logical Layer

Normal block-oriented devices present a consistent view of data storage with each block being a small fixed size ranging from 512 bytes to 4,096 bytes. Flash memory does not act like normal block-oriented devices though. The underlying hardware is separated into erase block regions of which there can be four. Each erase block region can hold a number of erase blocks of a fixed size. These fixed sizes can be any size that is a power of two. For example, on the WRT54GL platform, Flash is separated into two erase block regions, one with 8 - 8 KB erase blocks and the other with 63 - 64 KB erase blocks.

To avoid the user level programmer from having to deal with this inconsistent view of erase blocks, the logical layer of the Flash driver splits all of Flash memory into uniformly sized logical blocks (at present this is 512 byte blocks). When a call to read() occurs, the logical layer will determine what erase block the logical block maps to, determine if the erase block has already been loaded into RAM and return a pointer to the cached data. Similarly, a call to write() will perform a mapping from logical to erase block and write the data to the cached memory. If too many erase blocks are stored in RAM, the logical layer will evict a block and if it has been modified since the read it will write it back to Flash memory.

Physical Layer

Once the logical to erase block mapping has occurred, the logical layer can pass the erase block stored in RAM to the physical layer to perform the low level hardware operations. At this layer, the software only deals in erase block units and uses manufacturer specific code. Currently, Embedded Xinu fully supports the Intel Standard Command Set (SCS) and the AMD/Samsung SCS is a work in progress.

Largely, the routines to handle the hardware follow similar concepts. When a non-read request is made to the physical layer the software steps through a series of operations to change an erase block from read-mode to program or erase mode. When this happens, the software is able to safely modify the data.

An interesting property of Flash memory is that certain devices allow program and erase operations to be suspended, so it may be possible to spin the physical layer off as a separate pre-emptible process. Unfortunately, while the Intel SCS supports suspend/resume operations the AMD/Samsung SCS does not, so this would lead to compatibility issues if implemented.

NVRAM

NVRAM settings are stored in Flash memory and take advantage of both the logical and physical layers of the Flash driver. When NVRAM is first initialized, the Flash driver determines what logical block the settings begin in and then begins reading and storing the settings into RAM. Each tuple is indexed into a hash table and allocated a piece of memory to store the data in. When a setting is changed, the original value is released from memory and the new value is added. If a value is requested, the driver will simply find the storage location and return the pointer to the data.

When the updated settings are committed to Flash, the NVRAM driver will discover the logical block to erase block mapping, create a complete erase block with the new settings, cause a write in the physical layer, and finally force a synchronization to commit the settings to Flash.